Course Information

Air Source Heat Pump

course-detail-img-1 course details banner mobile
  • course-detail-usp-img-2
    £850.00
  • course-detail-usp-img-3
    3 Days
  • course-detail-usp-img-2
    Intermediatte

About This Course

This Air Source Heat Pump training course offers qualified heating and plumbing engineers the opportunity to move into a high growth area for the future. This course covers both ground to water and air to water technologies and meets the training entry requirements for the Micro generation Certification Scheme (MCS). 

Thanks to legally binding targets to cut carbon and the introduction of the Renewable Heat Incentive (RHI), heat pumps are a natural development for the heating market and should be considered by any heating installation company or engineer; whether they work with gas, LPG, solid fuel, oil or bio-mass. 

The course is certified by LCL Awards and will give you a thorough understanding of heat pump technologies and the health and safety risks associated with them. You will learn all you need to know about the installation, commissioning and hand over of air source heat pumps as well as the maintenance requirements for inspecting and servicing them in the future. 

This recently redesigned regulated qualification has been brought up to date with industry / MCS requirements and is for learners that wish to demonstrate their knowledge in the Installation and Maintenance of Heat Pumps Systems (non-refrigerant circuits

Our students complete an intensive 3 Days training course:

  • The course will enable operatives to specify, survey, design and install domestic or small commercial heat pump systems, enlisting manufacturers support where required. Systems up to 24kW for ground source and 16kW for air source heat pumps are covered, plus the following areas:
  • Background to market Heat pump regulations and guidance Principles of ground and air source heat pump operation Heat pump collector types Heat distribution Pre-installation requirements Installation materials and methods Filling, flushing and testing Setting to work, commissioning Heat pump servicing and fault finding The course will enable operatives to specify, survey, design and install domestic or small commercial heat pump systems, enlisting manufacturers support where required.
  • Systems up to 24kW for ground source and 16kW for air source heat pumps are covered, plus the following areas: 
  • Background to market Heat pump regulations and guidance Principles of ground and air source heat pump operation Heat pump collector types Heat distribution Pre-installation requirements Installation materials and methods Filling, flushing and testing Setting to work, commissioning Heat pump servicing and fault finding The course will enable operatives to specify, survey, design and install domestic or small commercial heat pump systems, enlisting manufacturers support where required. Systems up to 24kW for ground source and 16kW for air source heat pumps are covered, plus the following areas: 
  • Background to market Heat pump regulations and guidance Principles of ground and air source heat pump operation Heat pump collector types Heat distribution Pre-installation requirements Installation materials and methods Filling, flushing and testing Setting to work, commissioning Heat pump servicing and fault finding 

Assessment Method

Practical and written test

Prerequisites

  • N/SVQ Level 2/3 in Plumbing or equivalent earlier certification that provides evidence of competence or
  • N/SVQ Level 2/3 in Heating and Ventilating (Domestic Installation) or equivalent earlier certification that provides evidence of competence or N/SVQ Level 2/3 in Heating and Ventilating (Industrial and Commercial Installation) or
  • Equivalent earlier certification that provides evidence of competence or N/SVQ Level 2/3 in Oil-Fired Technical Services or equivalent earlier certification that provides evidence of competence or
  • N/SVQ Level 2/3 in Gas Installation and Maintenance or equivalent earlier certification that provides evidence of competence
  • In addition, if not included in the above current certification in relation to:
  • WRAS Water Regulations/Water Bylaws
  • Energy Efficiency for Domestic Heating
  • Please note, we can offer the above training courses as part of a package deal

Apply Now

    Testimonials

    Practical workshops, a purpose built mock-house, individual bays, live gas supplies, and a full range

    logo
    Steve

    Central Heating Installer / Dudley

    testimonial-rating

    Brilliant course! If you want to know exactly how to use an analyser then this course is ideal. Would recommend to any installer who wants the full knowledge in a day!

    logo
    Johnson Harris

    Electrician / Birmingham

    testimonial-rating

    Get Training gave me great confidence and skills to continue with my electrics career! I am now ready to apply my fresh skills to my career.

    logo
    Matthew Fortt

    Gas Safe Engineer / Isle of Wight

    testimonial-rating

    The course was excellent, my trainer made the course very enjoyable and I wish I had come and done the course years ago, I enjoyed every minute.

    logo
    Carl Plant

    Electrical Engineer / Essex

    testimonial-rating

    The Part P course didn’t just give me the qualification but also gave me the confidence to leave the centre with enough knowledge and skills to actually do the job

    Get In Touch

    Practical workshops, a purpose built mock-house, individual bays, live gas supplies, and a full range

    Get In Touch

    Request A Call Back